Design of infrared electronic-toll-collection systems with extended communication areas and performance of data transmission

Wern Yarng Shieh, Chen Chien Hsu, Shen Lung Tung, Po Wen Lu, Ti Ho Wang, Shyang Lih Chang

Research output: Contribution to journalArticle

20 Citations (Scopus)

Abstract

Based on our previous works in the design of an infrared emitter for electronic-toll-collection (ETC) applications, we use the unidirectional cosinen functions to approximate the irregular radiation pattern for typical infrared low-cost commercial light-emitting diodes (LEDs) with a half-intensity angle Φ1/2 = 10°. With the aid of this approximation, the main characteristics of the performance of an infrared ETC system utilizing this type of LED as the emitter can be investigated based on the received signal strength of the system. For onoff keying, a simple model connecting the received signal strength and the bit error rate (BER) of the system is further established. From the calculated or the measured received signal strength of the system, it is not difficult to estimate the system performance in terms of the BER by this simple model. Roughly speaking, for a typical setting of the circuit parameters and a typical uplink and downlink data-transmission protocol, the data transmission can be very successful in terms of a very low BER if the received signal strength is 1.3 times stronger than the signal strength received at the communication boundary. The emitter presented in this paper is able to produce a relatively extended communication area in the vehicle-traveling direction, resulting in longer communication time interval for the data transmission between the onboard unit (OBU) and the roadside unit (RSU) than conventional emitters. Furthermore, the design presented in this paper is validated by experimental measurement to demonstrate its effectiveness.

Original languageEnglish
Article number5535181
Pages (from-to)25-35
Number of pages11
JournalIEEE Transactions on Intelligent Transportation Systems
Volume12
Issue number1
DOIs
Publication statusPublished - 2011 Mar 1

Fingerprint

Toll collection
Bit error rate
Data communication systems
Infrared radiation
Light emitting diodes
Communication
Roadsides
Networks (circuits)
Costs

Keywords

  • Bit error rate (BER)
  • dedicated short-range communication (DSRC)
  • electronic toll collection (ETC)
  • infrared communication
  • intelligent transportation system (ITS)
  • onoff keying (OOK)

ASJC Scopus subject areas

  • Automotive Engineering
  • Mechanical Engineering
  • Computer Science Applications

Cite this

Design of infrared electronic-toll-collection systems with extended communication areas and performance of data transmission. / Shieh, Wern Yarng; Hsu, Chen Chien; Tung, Shen Lung; Lu, Po Wen; Wang, Ti Ho; Chang, Shyang Lih.

In: IEEE Transactions on Intelligent Transportation Systems, Vol. 12, No. 1, 5535181, 01.03.2011, p. 25-35.

Research output: Contribution to journalArticle

@article{049fd214f6c7412dba8631a3269f87e7,
title = "Design of infrared electronic-toll-collection systems with extended communication areas and performance of data transmission",
abstract = "Based on our previous works in the design of an infrared emitter for electronic-toll-collection (ETC) applications, we use the unidirectional cosinen functions to approximate the irregular radiation pattern for typical infrared low-cost commercial light-emitting diodes (LEDs) with a half-intensity angle Φ1/2 = 10°. With the aid of this approximation, the main characteristics of the performance of an infrared ETC system utilizing this type of LED as the emitter can be investigated based on the received signal strength of the system. For onoff keying, a simple model connecting the received signal strength and the bit error rate (BER) of the system is further established. From the calculated or the measured received signal strength of the system, it is not difficult to estimate the system performance in terms of the BER by this simple model. Roughly speaking, for a typical setting of the circuit parameters and a typical uplink and downlink data-transmission protocol, the data transmission can be very successful in terms of a very low BER if the received signal strength is 1.3 times stronger than the signal strength received at the communication boundary. The emitter presented in this paper is able to produce a relatively extended communication area in the vehicle-traveling direction, resulting in longer communication time interval for the data transmission between the onboard unit (OBU) and the roadside unit (RSU) than conventional emitters. Furthermore, the design presented in this paper is validated by experimental measurement to demonstrate its effectiveness.",
keywords = "Bit error rate (BER), dedicated short-range communication (DSRC), electronic toll collection (ETC), infrared communication, intelligent transportation system (ITS), onoff keying (OOK)",
author = "Shieh, {Wern Yarng} and Hsu, {Chen Chien} and Tung, {Shen Lung} and Lu, {Po Wen} and Wang, {Ti Ho} and Chang, {Shyang Lih}",
year = "2011",
month = "3",
day = "1",
doi = "10.1109/TITS.2010.2057508",
language = "English",
volume = "12",
pages = "25--35",
journal = "IEEE Transactions on Intelligent Transportation Systems",
issn = "1524-9050",
publisher = "Institute of Electrical and Electronics Engineers Inc.",
number = "1",

}

TY - JOUR

T1 - Design of infrared electronic-toll-collection systems with extended communication areas and performance of data transmission

AU - Shieh, Wern Yarng

AU - Hsu, Chen Chien

AU - Tung, Shen Lung

AU - Lu, Po Wen

AU - Wang, Ti Ho

AU - Chang, Shyang Lih

PY - 2011/3/1

Y1 - 2011/3/1

N2 - Based on our previous works in the design of an infrared emitter for electronic-toll-collection (ETC) applications, we use the unidirectional cosinen functions to approximate the irregular radiation pattern for typical infrared low-cost commercial light-emitting diodes (LEDs) with a half-intensity angle Φ1/2 = 10°. With the aid of this approximation, the main characteristics of the performance of an infrared ETC system utilizing this type of LED as the emitter can be investigated based on the received signal strength of the system. For onoff keying, a simple model connecting the received signal strength and the bit error rate (BER) of the system is further established. From the calculated or the measured received signal strength of the system, it is not difficult to estimate the system performance in terms of the BER by this simple model. Roughly speaking, for a typical setting of the circuit parameters and a typical uplink and downlink data-transmission protocol, the data transmission can be very successful in terms of a very low BER if the received signal strength is 1.3 times stronger than the signal strength received at the communication boundary. The emitter presented in this paper is able to produce a relatively extended communication area in the vehicle-traveling direction, resulting in longer communication time interval for the data transmission between the onboard unit (OBU) and the roadside unit (RSU) than conventional emitters. Furthermore, the design presented in this paper is validated by experimental measurement to demonstrate its effectiveness.

AB - Based on our previous works in the design of an infrared emitter for electronic-toll-collection (ETC) applications, we use the unidirectional cosinen functions to approximate the irregular radiation pattern for typical infrared low-cost commercial light-emitting diodes (LEDs) with a half-intensity angle Φ1/2 = 10°. With the aid of this approximation, the main characteristics of the performance of an infrared ETC system utilizing this type of LED as the emitter can be investigated based on the received signal strength of the system. For onoff keying, a simple model connecting the received signal strength and the bit error rate (BER) of the system is further established. From the calculated or the measured received signal strength of the system, it is not difficult to estimate the system performance in terms of the BER by this simple model. Roughly speaking, for a typical setting of the circuit parameters and a typical uplink and downlink data-transmission protocol, the data transmission can be very successful in terms of a very low BER if the received signal strength is 1.3 times stronger than the signal strength received at the communication boundary. The emitter presented in this paper is able to produce a relatively extended communication area in the vehicle-traveling direction, resulting in longer communication time interval for the data transmission between the onboard unit (OBU) and the roadside unit (RSU) than conventional emitters. Furthermore, the design presented in this paper is validated by experimental measurement to demonstrate its effectiveness.

KW - Bit error rate (BER)

KW - dedicated short-range communication (DSRC)

KW - electronic toll collection (ETC)

KW - infrared communication

KW - intelligent transportation system (ITS)

KW - onoff keying (OOK)

UR - http://www.scopus.com/inward/record.url?scp=79952069654&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=79952069654&partnerID=8YFLogxK

U2 - 10.1109/TITS.2010.2057508

DO - 10.1109/TITS.2010.2057508

M3 - Article

AN - SCOPUS:79952069654

VL - 12

SP - 25

EP - 35

JO - IEEE Transactions on Intelligent Transportation Systems

JF - IEEE Transactions on Intelligent Transportation Systems

SN - 1524-9050

IS - 1

M1 - 5535181

ER -